Everybody is bound to have their personal theory in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bath tub isn't specifically rocket science, but it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is readily accessible, the job can relocate easily; if you need to open a wall to get rid of the old bathtub and position the brand-new tub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to vacate the old bathtub and also embeded in the new one. Make sure you have actually qualified on your own for the task and are comfortable attempting it. Rather than employing a contractor to take control of a halfway-completed task, it is much better to consider using one before you begin. Possibilities are you might need a specialist plumber to make tube links.
This post will certainly aid you set up a brand-new tub in your bathroom if you have already purchased a brand-new bathtub and also do not need to transform the arrangement of your previous water pipelines.
Your tools and material list need to make up the following:
Planning for the Installation
Firstly, the supporting framework supplied with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to avoid strain on the bath tub.
Fit the flexible tap connectors to the bottom of both taps using 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is disconnect the water system. After doing so, activate the taps to drain any water continuing to be in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted access that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Before going on to fit the new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, put the tub in the called for position. The wood boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 little points.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the tub until the level checks out degree.
To set up taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water supply and also check all joints and new pipework for leakages and also tighten them if required. Load the tub and additionally inspect the overflow electrical outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bath tub ought to wait up until the bathtub has actually been used a minimum of once as this will certainly resolve it right into its last placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin making certain that the washers are in place between the faucet as well as the sink. Protect the faucet in position with the producer offered backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap ports. The former type must be connected to the tap ends initially, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to crack an inflexible seal, creating the water to pass through the wall surface between the bathroom and also the tiling, causing complications with moisture as well as feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to allow for the motion experienced when the tub is in use. The sealer can split relatively early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that content on Installing A Bathtub when doing a lookup on the web. In case you liked our blog posting please remember to share it. We love reading our article about Tools You Need to Install a New Bathtub .
Expertise available here.